 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ADVANCED INFORMATION MX26L1620 16M-BIT [1M x 16] CMOS MULTIPLE-TIME-PROGRAMMABLE EPROM FEATURES * 1,048,576 x 16 byte structure * Single Power Supply Operation - 2.7 to 3.6 volt for read, erase, and program operations Low Vcc write inhibit is equal to or less than 2.5V Compatible with JEDEC standard High Performance - Fast access time: 90/120ns (typ.) - Fast program time: 35s/chip (typ.) - Fast erase time: 45s/chip (typ.) Low Power Consumption - Low active read current: 10mA (typ.) at 5MHz - Low standby current: 30uA (typ.) Minimum 100 erase/program cycle * 10-year data retention * Status Reply - Data polling & Toggle bits provide detection of program and erase operation completion 12V ACC input pin provides accelerated program capability Output voltages and input voltages on the device is determined by the voltage on the VI/O pin. - VI/O voltage range:1.65V~3.6V Package - 44-Pin SOP - 48-Pin TSOP - 48-Ball CSP * * * * * * * * GENERAL DESCRIPTION The MX26L1620 is a 16M bit MTP EPROMTM organized as 1M bytes of 16 bits. MXIC's MTP EPROMTM offer the most cost-effective and reliable read/write non-volatile random access memory. The MX26L1620 is packaged in 44-pin SOP, 48-pin TSOP and 48-ball CSP. It is designed to be reprogrammed and erased in system or in standard EPROM programmers. The standard MX26L1620 offers access time as fast as 90ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention, the MX26L1620 has separate chip enable (CE) and output enable OE controls. MXIC's MTP EPROMTM augment EPROM functionality with in-circuit electrical erasure and programming. The MX26L1620 uses a command register to manage this functionality. MXIC's MTP EPROMTM technology reliably stores memory contents even after 100 erase and program cycles. The MXIC cell is designed to optimize the erase and program mechanisms. In addition, the combination of advanced tunnel oxide processing and low internal electric fields for erase and programming operations produces reliable cycling. The MX26L1620 uses a 2.7V to 3.6V VCC supply to perform the High Reliability Erase and auto Program/ Erase algorithms. The highest degree of latch-up protection is achieved with MXIC's proprietary non-epiprocess. Latch-up protection is proved for stresses up to 100 milliamps on address and data pin from -1V to VCC +1V. P/N:PM0827 REV. 0.4, JAN. 31, 2002 1 MX26L1620 PIN CONFIGURATION 48 CSP 1. Ball pitch=0.75mm for MX26L1620XA (TOP view, Ball down) 1 2 3 4 5 6 7 8 A A13 A11 A8 ACC NC A19 A7 A4 B A14 A10 WE RESET A18 A17 A5 A2 C A15 A12 A9 NC NC A6 A3 A1 7.0 mm D A16 Q14 Q5 Q11 Q2 Q8 CE A0 E V I/O Q15 Q6 Q12 Q3 Q9 Q0 GND F GND Q7 Q13 Q4 VCC Q10 Q1 OE 8.0 mm 2. Ball pitch=0.8mm for MX26L1620XB(TOP view, Ball down) A B C D E F G H 6 A13 A12 A14 A15 A16 V I/O Q15 GND 5 A9 A8 A10 A11 Q7 Q14 Q13 Q6 4 WE RESET NC A19 Q5 Q12 VCC Q4 7.0 mm 3 NC ACC A18 NC Q2 Q10 Q11 Q3 2 A7 A17 A6 A5 Q0 Q8 Q9 Q1 1 A3 A4 A2 A1 A0 CE OE GND 8.0 mm P/N:PM0827 REV. 0.4, JAN. 31, 2002 2 MX26L1620 44 SOP NC A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE GND OE Q0 Q8 Q1 Q9 Q2 Q10 Q3 Q11 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 NC A19 A8 A9 A10 A11 A12 A13 A14 A15 A16 WE GND Q15 Q7 Q14 Q6 Q13 Q5 Q12 Q4 VCC 48 TSOP A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE RESET ACC VCC A19 A18 A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 VI/O GND Q15 Q7 Q14 Q6 Q13 Q5 Q12 Q4 VCC Q11 Q3 Q10 Q2 Q9 Q1 Q8 Q0 OE GND CE A0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 MX26L1620 MX26L1620 PIN DESCRIPTION SYMBOL A0~A19 Q0~Q15 CE WE OE RESET VCC ACC V I/O GND NC PIN NAME Address Input Data Inputs/Outputs Chip Enable Input Write Enable Input Output Enable Input Hardware Reset Pin, Active Low +3.0V single power supply Hardware Acceleration Pin I/O power supply (for 48 TSOP and 48 CSP package only) Device Ground Pin Not Connected Internally LOGIC SYMBOL 20 A0-A19 Q0-Q15 16 CE OE WE RESET ACC P/N:PM0827 REV. 0.4, JAN. 31, 2002 3 MX26L1620 BLOCK DIAGRAM WRITE CE OE WE CONTROL INPUT LOGIC HIGH VOLTAGE MACHINE (WSM) PROGRAM/ERASE STATE X-DECODER MX26L1620 FLASH ARRAY ARRAY STATE REGISTER ADDRESS LATCH A0-A19 AND BUFFER SENSE AMPLIFIER Y-DECODER Y-PASS GATE SOURCE HV COMMAND DATA DECODER PGM DATA HV COMMAND DATA LATCH PROGRAM DATA LATCH Q0-Q15 I/O BUFFER P/N:PM0827 REV. 0.4, JAN. 31, 2002 4 MX26L1620 AUTOMATIC PROGRAMMING The MX26L1620 is word programmable using the Automatic Programming algorithm. The Automatic Programming algorithm makes the external system do not need to have time out sequence nor to verify the data programmed. The typical chip programming time at room temperature of the MX26L1620 is less than 20 seconds. All data are latched on the rising edge of WE or CE, whichever happens later. MXIC's Flash technology combines years of EPROM experience to produce the highest levels of quality, reliability, and cost effectiveness. The MX26L1620 electrically erases all bits simultaneously using Fowler-Nordheim tunneling. The bytes are programmed by using the EPROM programming mechanism of hot electron injection. During a program cycle, the state-machine will control the program sequences and command register will not respond to any command set. After the state machine has completed its task, it will allow the command register to respond to its full command set. AUTOMATIC PROGRAMMING ALGORITHM MXIC's Automatic Programming algorithm require the user to only write program set-up commands (including 2 unlock write cycle and A0H) and a program command (program data and address). The device automatically times the programming pulse width, provides the program verification, and counts the number of sequences. A status bit similar to DATA polling and a status bit toggling between consecutive read cycles, provide feedback to the user as to the status of the programming operation. AUTOMATIC CHIP ERASE The entire chip is bulk erased using 50 ms erase pulses according to MXIC's Automatic Chip Erase algorithm. Typical erasure at room temperature is accomplished in less than 45 seconds. The Automatic Erase algorithm automatically programs the entire array prior to electrical erase. The timing and verification of electrical erase are controlled internally within the device. AUTOMATIC ERASE ALGORITHM MXIC's Automatic Erase algorithm requires the user to write commands to the command register using standard microprocessor write timings. The device will automatically pre-program and verify the entire array. Then the device automatically times the erase pulse width, provides the erase verification, and counts the number of sequences. A status bit toggling between consecutive read cycles provides feedback to the user as to the status of the programming operation. Register contents serve as inputs to an internal statemachine which controls the erase and programming circuitry. During write cycles, the command register internally latches address and data needed for the programming and erase operations. All address are latched on the falling edge of WE or CE, whichever happens later. P/N:PM0827 REV. 0.4, JAN. 31, 2002 5 MX26L1620 Table 1. BUS OPERATION(1) Operation Read Write(Note 1) Standby Output Disable Reset CE L L VCC0.3V L X OE L H X H X WE H L X H X RESET H H VCC0.3V H L Address AIN AIN X X X Q15~Q0 DOUT DIN High-Z High-Z High-Z Legend: L=Logic LOW=VIL,H=Logic High=VIH,VID=12.00.5V,X=Don't Care, AIN=Address IN, DIN=Data IN, DOUT=Data OUT Notes: 1. When the ACC pin is at VHH, the device enters the accelerated program mode. See "Accelerated Program Operations" for more information. Table 2. AUTOSELECT CODES (High Voltage Method) A5 Operation Read Silicon ID Manufactures Code Read Silicon ID Device Code Secured Silscon Sector Indicator Bit(Q7) L L H H H X L X VID X X xx88h (factory locked) xx08h (non-factory locked) L L H H L X L X VID X X 22FEH CE L OE L WE H A0 L A1 L to A2 X L A6 A8 to A7 X VID A9 A14 to A10 X X00 C2H A15~A21 Q15~Q0 P/N:PM0827 REV. 0.4, JAN. 31, 2002 6 MX26L1620 REQUIREMENTS FOR READING ARRAY DATA To read array data from the outputs, the system must drive the CE and OE pins to VIL. CE is the power control and selects the device. OE is the output control and gates array data to the output pins. WE should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory contect occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid address on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. pins and the other one is using RESET pin only. When using both pins of CE and RESET, a CMOS Standby mode is achieved with both pins held at Vcc 0.3V. Under this condition, the current consumed is less than 50uA (typ.). If both of the CE and RESET are held at VIH, but not within the range of VCC 0.3V, the device will still be in the standby mode, but the standby currect will be larger. During Auto Algorithm operation, Vcc active current (Icc2) is required even CE = "H" until the operation is complated. The device can be read with standard access time (tCE) from either of these standby modes. When using only RESET, a CMOS standby mode is achieved with RESET input held at Vss 0.3V, Under this condition the current is consumed less than 50uA (typ.). Once the RESET pin is taken high,the device is back to active without recovery delay. In the standby mode the outputs are in the high impedance state, independent of the OE input. MX26L1620 is capable to provide the Automatic Standby Mode to restrain power consumption during read-out of data. This mode can be used effectively with an application requested low power consumption such as handy terminals. To active this mode, MX26L1620 automatically switch themselves to low power mode when MX26L1620 addresses remain stable during access time of tACC+30ns. It is not necessary to control CE, WE, and OE on the mode. Under the mode, the current consumed is typically 50uA (CMOS level). WRITE COMMANDS/COMMAND SEQUENCES To program data to the device, the system must drive WE and CE to VIL, and OE to VIH. An erase operation can erase the entire device. The "Writing specific address and data commands or sequences into the command register initiates device operations. Table 1 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence resets the device to reading array data."section has details on erasing the entire chip. After the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal reqister (which is separate from the memory array) on Q15-Q0. Standard read cycle timings apply in this mode. Refer to the Autoselect Mode and Autoselect Command Sequence section for more information. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The "AC Characteristics" section contains timing specification table and timing diagrams for write operations. OUTPUT DISABLE With the OE input at a logic high level (VIH), output from the devices are disabled. This will cause the output pins to be in a high impedance state. RESET OPERATION The RESET pin provides a hardware method of resetting the device to reading array data. When the RESET pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET pluse. The STANDBY MODE MX26L1620 can be set into Standby mode with two different approaches. One is using both CE and RESET P/N:PM0827 REV. 0.4, JAN. 31, 2002 7 MX26L1620 device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitated once the device is ready to accept another command sequence, to ensure data integrity Current is reduced for the duration of the RESET pulse. When RESET is held at VSS0.3V, the device draws CMOS standby current (ICC4). If RESET is held at VIL but not within VSS0.3V, the standby current will be greater. The RESET pin may be tied to system reset circuitry. A system reset would that also reset the MTP EPROM. Refer to the AC Characteristics tables for RESET parameters and to Figure 14 for the timing diagram. Table 3 VCC / VI/O Voltage Range Part No. VCC=2.7V to 3.6VVCC=2.7V to 3.6V VI/O=2.7V to 3.6VVI/O=1.65V to 2.6V MX26L1620-90 MX26L1620-12 90ns 120ns 100ns 130ns Notes: Typical values measured at VCC=2.7V to 3.6V, VI/O=2.7V to 3.6V DATA PROTECTION The MX26L1620 is designed to offer protection against accidental erasure or programming caused by spurious system level signals that may exist during power transition. During power up the device automatically resets the state machine in the Read mode. In addition, with its control register architecture, alteration of the memory contents only occurs after successful completion of specific command sequences. The device also incorporates several features to prevent inadvertent write cycles resulting from VCC power-up and power-down transition or system noise. SILICON ID READ OPERATION MTP EPROM are intended for use in applications where the local CPU alters memory contents. As such, manufacturer and device codes must be accessible while the device resides in the target system. EPROM programmers typically access signature codes by raising A9 to a high voltage. However, multiplexing high voltage onto address lines is not generally desired system design practice. MX26L1620 provides hardware method to access the silicon ID read operation. Which method requires VID on A9 pin, VIL on CE, OE, A6, and A1 pins. Which apply VIL on A0 pin, the device will output MXIC's manufacture code of C2H. Which apply VIH on A0 pin, the device will output MX26L1620 device code of 22FEH. SECURED SILICON SECTOR The MX26L1620 features a Flash memory region where the system may access through a command sequence to create a permant part identification as so called Electronic Serial Number (ESN) in the device. Once this region is programmed, any further modification on the region is impossible. The secured silicon sector is a 512 words in length, and uses a Secured Silicon Sector Indicator Bit (Q7) to indicate whether or not the Secured Silicon Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevent duplication of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. The MX26L1620 offers the device with Secured Silicon Sector either factory locked or custor lockable. The factory-locked version is always protected when shipped from the factory , and has the Secured Silicon Sector Indicator Bit permanently set to a "1". The customerlockable version is shipped with the Secured Silicon Sector unprotected, allowing customer to utilize that sector in any form they prefer. The customer-lockable ver- VI/O PIN OPERATION MX26L1620 is capable to provide the I/O prower supply (VI/O) pin to control Input/Output voltage levels of the device. The data outputs and voltage tolerated at its data input is determined by the voltage on the VI/O pin. This device is allows to operate in 1.8V or 3V system as required. P/N:PM0827 REV. 0.4, JAN. 31, 2002 8 MX26L1620 sion has the secured sector Indicator Bit permanently set to a "0". Therefore, the Secured Silicon Sector Indicator Bit permanently set to a "0". Therefore, the Second Silicon Sector Indicator Bit prevents customer, lockable device from being used to replace devices that are factory locked. The system access the Secured Silicon Sector through a command sequence (refer to "Enter Secured Silicon/ Exit Secured Silicon Sector command Sequence). After the system has written the Enter Secured Silicon Sector command sequence, it may read the Secured Silicon Sector by using the address normally occupied by the address 000000h-0001FFh. This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending command to address 000000h-0001FFFh. FACTORY LOCKED:Secured Silicon Sector Programmed and Protected At the Factory In device with an ESN, the Secured Silicon Sector is protected when the device is shipped from the factory. The Secured Silicon Sector cannot be modified in any way. A factory locked device has an 8-word random ESN at address 000000h-000007h. CUSTOMER LOCKABLE:Secured Silicon Sector NOT Programmed or Protected At the Factory As an alternative to the factory-locked version, the device may be ordered such that the customer may program and protect the 512-word Secured Silicon Sector. Programming and protecting the Secured Silicon Sector must be used with caution since, once protected, there is no procedure available for unprotecting the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. The Secured Silicon Sector area can be protected using the following procedures: Write the three-cycle Enter Secured Silicon Sector Region command sequence. This allows in-system protection of the Secured Silicon Sector without raising any device pin to a high voltage. Note that method is only applicable to the Secured Silicon Sector. Once the Secured Silicon Sector is programmed, locked and verified, the system must write the Exit Secured Silicon Sector Region command sequence to return to reading and writing the remainder of the array. LOW VCC WRITE INHIBIT When VCC is less than VLKO the device does not accept any write cycles. This protects dataduring VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets. Subsequent writes are ignored until VCC is greater thanVLKO. The system must provide the proper signals to the control pins to prevent unintentional write when VCC is greater than VLKO. WRITE PULSE "GLITCH" PROTECTION Noise pulses of less than 5ns(typical) on CE or WE will not initiate a write cycle. LOGICAL INHIBIT Writing is inhibited by holding any one of OE = VIL, CE = VIH or WE = VIH. To initiate a write cycle CE and WE must be a logical zero while OE is a logical one. POWER-UP SEQUENCE The MX26L1620 powers up in the Read only mode. In addition, the memory contents may only be altered after successful completion of the predefined command sequences. P/N:PM0827 REV. 0.4, JAN. 31, 2002 9 MX26L1620 SOFTWARE COMMAND DEFINTIONS Device operations are selected by writing specific address and data sequences into the command register. Writing incorrect address and data values or writing them in the improper sequence will reset the device to the read mode. Table 4 defines the valid register command sequences. Either of the two reset command sequences will reset the device(when applicable). All addresses are latched on the falling edge of WE or CE, whichever happens later. All data are latched on rising edge of WE or CE, whichever happens first. TABLE4. MX26L1620 COMMAND DEFINITIONS First Bus Command Bus Cycle Read(Note 5) Reset(Note 6) Autoselect(Note 7) Manufacturer ID Device ID Secured Sector Factory Protect Enter Secured Silicon Sector Exit Secured Silicon Sector Porgram Chip Erase Deep power down 4 6 3 555 555 555 AA AA AA 2AA 2AA 2AA 55 55 55 555 555 555 A0 80 C0 PA 555 PD AA 2AA 55 555 10 4 555 AA 2AA 55 555 90 xxx 00 3 555 AA 2AA 55 555 88 4 4 4 555 555 555 AA AA AA 2AA 2AA 2AA 55 55 55 555 555 555 90 90 90 X00 X01 x03 C2 22FE see Note9 1 1 Cycle Addr RA XXX Data RD F0 Second Bus Third Bus Cycle Addr Cycle Data Addr Fourth Bus Cycle Data Addr Data Fifth Bus Cycle Sixth Bus Cycle Addr Data Addr Data Legend: X=Don't care RA=Address of the memory location to be read. RD=Data read from location RA during read operation. PA=Address of the memory location to be programmed. Addresses are latched on the falling edge of the WE or CE pulse. PD=Data to be programmed at location PA. Data is latched on the rising edge of WE or CE pulse. Notes: 1.See Table 1 for descriptions of bus operations. 2.All values are in hexadecimal. 3.Except when reading array or autoselect data, all bus cycles are write operation. 4.Address bits are don't care for unlock and command cycles, except when PA is required. 5.No unlock or command cycles required when device is in read mode. 6.The Reset command is required to return to the read mode when the device is in the autoselect mode or if Q5 goes high. 7.The fourth cycle of the autoselect command sequence is a read cycle. 8.Command is valid when device is ready to read array data or when device is in autoselect mode. 9.The data is 88h for factory locked and 08h for non-factory locked. P/N:PM0827 REV. 0.4, JAN. 31, 2002 10 MX26L1620 READING ARRAY DATA The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is also ready to read array data after completing an Automatic Program or Automatic Erase algorithm. The system must issue the reset command to re-enable the device for reading array data if Q5 goes high, or while in the autoselect mode. See the "Reset Command" section, next. ID READ command. The device then enters the SILICON ID READ mode, and the system may read at any address any number of times, without init iating another command sequence. A read cycle at address XX00h retrieves the manufacturer code. A read cycle at address XX01h returns the device code. The system must write the reset command to exit the autoselect mode and return to reading array data. WORD PROGRAM COMMAND SEQUENCE The command sequence requires four bus cycles, and is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide fur ther controls or timings. The device automatically generates the program pulses and verifies the programmed cell margin. Table 4 shows the address and data requirements for the byte program command sequence. When the Embedded Program algorithm is complete, the device then returns to reading array data and addresses are no longer latched. The system can determine the status of the program operation by using Q7, Q6. See "Write Operation Status" for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the programming operation. The Word Program command sequence should be reinitiated once the device has reset to reading array data, to ensure data integrity. Programming is allowed in any sequence. A bit cannot be programmed from a "0" back to a "1". Cause the Data Polling algorithm to indicate the operation was successful. However, a succeeding read will show that the data is still "0". Only erase operations can convert a "0" to a "1". RESET COMMAND Writing the reset command to the device resets the device to reading array data. Address bits are don't care for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to reading array data. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to reading array data. Once programming begins,however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an SILICON ID READ command sequence. Once in the SILICON ID READ mode, the reset command must be written to return to reading array data. If Q5 goes high during a program or erase operation, writing the reset command returns the device to reading array data. SILICON ID READ COMMAND SEQUENCE The SILICON ID READ command sequence allows the host system to access the manufacturer and devices codes, and determine whether or not. Table 4 shows the address and data requirements. This method is an alternative to that shown in Table 1, which is intended for EPROM programmers and requires VID on address bit A9. The SILICON ID READ command sequence is initiated by writing two unlock cycles, followed by the SILICON P/N:PM0827 ACCELERATED PROGRAM OPERATIONS The device offers accelerated program operations through the ACC pin. When the system asserts VHH on the ACC pin, the device automatically bypass the two "Unlock" write cycle. The device uses the higher voltage on the ACC pin to accelerate the operation. Note that the ACC pin must not be at VHH any operation other than accelerated programming, or device damage may result. REV. 0.4, JAN. 31, 2002 11 MX26L1620 SETUP AUTOMATIC CHIP ERASE Chip erase is a six-bus cycle operation. There are two "unlock" write cycles. These are followed by writing the "set-up" command 80H. Two more "unlock" write cycles are then followed by the chip erase command 10H. The MX26L1620 contains a Silicon-ID-Read operation to supplement traditional PROM programming methodology. The operation is initiated by writing the read silicon ID command sequence into the command register. Following the command write, a read cycle with A6=VIL, A1=VIL, A0=VIL retrieves the manufacturer code of C2H. A read cycle with A6=VIL, A1=VIL, A0=VIH returns the device code of 22FEH for MX26L1620. all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 4 shows the address and data requirements for the chip erase command sequence. Any commands written to the chip during the Automatic Erase algorithm are ignored. Note that a hardware reset during the chip erase operation immediately terminates the operation. The Chip Erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. The system can determine the status of the erase operation by using Q7, Q6. See "Write Operation Status" for information on these status bits. When the Automatic Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. Figure 5 illustrates the algorithm for the erase operation.See the Erase/Program Operations tables in "AC Characteristics" for parameters, and to Figure 4 for timing diagrams. AUTOMATIC CHIP ERASE COMMAND The device does not require the system to preprogram prior to erase. The Automatic Erase algorithm automatically preprograms and verifies the entire memory for an TABLE 5. SILICON ID CODE Pins A0 A1 A6 Q15 | Q8 00H 22H Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Code(Hex) Manufacture code VIL VIL VIL VIL 1 1 1 1 0 1 0 1 0 1 0 1 1 1 0 0 00C2H 22FEH Device code for MX26L1620 VIH VIL WRITE OPERSTION STATUS The device provides several bits to determine the status of a write operation: Q5, Q6, Q7. The following subsections describe the functions of these bits. Q7, and Q6 each offer a method for determining whether a program or erase operation is complete or in progress. These three bits are discussed first. Table 6. Write Operation Status Status Q7 Q6 Note1 In Progress Word Program in Auto Program Algorithm Auto Erase Algorithm Exceeded Word Program in Auto Program Algorithm Q7 0 Q7 0 Toggle Toggle Toggle Toggle 0 0 1 1 Q5 Time Limits Auto Erase Algorithm Notes: 1.Performing successive read operations from any address will cause Q6 to toggle. P/N:PM0827 REV. 0.4, JAN. 31, 2002 12 MX26L1620 Q7: Data Polling The Data Polling bit, Q7, indicates to the host sys-tem whether an Automatic Algorithm is in progress or completed. Data Polling is valid after the rising edge of the final WE pulse in the program or erase command sequence. During the Automatic Program algorithm, the device outputs on Q7 the complement of the datum programmed to Q7. This Q7 status also applies to programming during Er ase Suspend. When the Automatic Program algorithm is complete, the device outputs the datum programmed to Q7. The system must provide the program address to read valid status information on Q7. During the Automatic Erase algorithm, Data Polling produces a "0" on Q7. When the Automatic Erase algorithm is complete. Data Polling produces a "1" on Q7. This is analogous to the complement/true datum out-put described for the Automatic Program algorithm: the erase function changes all the bits to "1" prior to this, the device outputs the "complement," or "0"." If this time-out condition occurs during sector erase operation, it specifies that a is bad and it may not be reused. Write the Reset command sequence to the device, and then execute program or erase command sequence. This allows the system to continue to use the other active sectors in the device. If this time-out condition occurs during the chip erase operation, it specifies that the entire chip is bad. If this time-out condition occurs during the word programming operation, the word is bad and maynot be reused, (other word are still functional and can be reused). Q6:Toggle BIT I Toggle Bit I on Q6 indicates whether an Automatic Program or Erase algorithm is in progress or complete. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE or CE, whichever happens first pulse in the command sequence(prior to the program or erase operation). During an Automatic Program or Erase algorithm operation, successive read cycles to any address cause Q6 to toggle. The system may use either OE or CE to control the read cycles. When the operation is complete, Q6 stops toggling. Q5:Program/Erase Timing Q5 will indicate if the program or erase time has exceeded the specified limits(internal pulse count). Under these conditions Q5 will produce a "1". This time-out condition indicates that the program or erase cycle was not successfully completed. Data Polling and Toggle Bit are the only operating functions of the device under this condition. P/N:PM0827 REV. 0.4, JAN. 31, 2002 13 MX26L1620 ABSOLUTE MAXIMUM RATINGS Storage Temperature Plastic Packages . . . . . . . . . . . . . ..... -65oC to +150oC Ambient Temperature with Power Applied. . . . . . . . . . . . . .... -65oC to +125oC Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V A9, OE, and RESET (Note 2) . . . . . . . . . . . ....-0.5 V to +12.5 V All other pins (Note 1) . . . . . . . -0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) . . . . . . 200 mA Notes: 1. Minimum DC voltage on input or I/O pins is -0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 6. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 7. 2. Minimum DC input voltage on pins A9, OE, and RESET is -0.5 V. During voltage transitions, A9, OE, and RESET may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 6. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to 14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under "Absolute Maximum Rat-ings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. OPERATING RATINGS Commercial (C) Devices Ambient Temperature (TA ). . . . . . . . . . . . 0C to +70 C Industrial (I) Devices C Ambient Temperature (TA ). . . . . . . . . . -40 to +85C VCC Supply Voltages VCC for full voltage range. . . . . . . . . . . +2.7 V to 3.6 V Operating ranges define those limits between which the functionality of the device is guaranteed. P/N:PM0827 REV. 0.4, JAN. 31, 2002 14 MX26L1620 DC CHARACTERISTICS TA=0 to 70 VCC=2.7V~3.6V C C, Parameter Description I LI Input Load Current (Note 1) Test Conditions VIN = VSS to VCC , VCC = VCC max I LIT I LO A9 Input Load Current Output Leakage Current VCC=VCC max; A9 = 12.5V VOUT = VSS to VCC , VCC= VCC max ICC1 VCC Active Read Current (Notes1, 2) ICC2 VCC Active Write Current (Notes 1, 3, 4) ICC3 VCC Standby Current (CMOS) CE,RESET, (Note 1) ICC4 VCC Standby Current (TTL) (Note 1) ICC5 VCC Reset Current (Note 1) RESET = V SS 0.3 V, ACC = VCC 0.3 V IACC ACC Accelerated Program Current, Word VIL VIH VHH Input Low Voltage Input High Voltage Voltage for ACC Program Acceleration VID VOL Voltage for Autoselect Output Low Voltage VCC = 3.0 V 10% IOL= 4.0mA,VCC=VCC min IOH=-2.0mA,VCC=VCC min 0.85VI/O IOH=-100uA,VCC=VCC min VI/O-0.4 2.3 2.5 11.5 12.5 0.45 0.85VI/O VI/O-0.4 2.3 2.5 11.5 12.5 0.45 V V V V V VCC = 3.0 V 10% CE=VIL, OE=VIH Acc pin Vcc pin -0.5 0.7xVcc 8.5 5 15 10 30 0.8 Vcc+0.3 VI/O-0.4 9.5 8.5 9.5 5 15 10 30 0.4 mA mA V V V 0.2 5 0.2 5 uA ACC=VCC 0.3V CE=VIH 0.5 1 0.5 1 mA 30 100 30 100 uA CE= VIL, OE = VIH 5 MHz 1 MHz CE= V IL , OE = V IH 9 2 26 16 4 30 9 2 26 16 4 30 mA mA mA 35 1.0 35 1.0 uA uA VI/O=2.7V~3.6V Min Typ Max 1.0 VI/O=1.65V~2.6V Min Typ Max 1.0 Unit uA VOH1 Output High Voltage VOH2 VLKO Low V CC Lock-Out Voltage (Note 4) Notes: 1. Maximum ICC specifications are tested with VCC = VCC max. 2. The ICC current listed is typically is less than 2 mA/MHz, with OE at V IH . Typical specifications are for VCC = 3.0 V. 3. ICC active while Embedded Erase or Embedded Program is in progress. 4. Not 100% tested. P/N:PM0827 REV. 0.4, JAN. 31, 2002 15 MX26L1620 SWITCHING TEST CIRCUITS TEST SPECIFICATIONS Test Condition 90 120 Output Load 1 TTL gate Output Load Capacitance, CL 30 100 (including jig capacitance) Input Rise and Fall Times 5 Input Pulse Levels 0.0-3.0 Input timing measurement 1.5 reference levels Output timing measurement 1.5 reference levels Unit pF ns V V V DEVICE UNDER TEST 2.7K ohm 3.3V CL 6.2K ohm DIODES=IN3064 OR EQUIVALENT KEY TO SWITCHING WAVEFORMS WAVEFROM INPUTS Steady Changing from H to L Changing from L to H Don't Care, Any Change Permitted Does Not Apply Changing, State Unknown Center Line is High Impedance State(High Z) OUTPUTS SWITCHING TEST WAVEFORMS 3.0V 1.5V Measurement Level VIO/2 0.0V INPUT OUTPUT P/N:PM0827 REV. 0.4, JAN. 31, 2002 16 MX26L1620 C C, AC CHARACTERISTICS TA=0 to 70 VCC=2.7V~3.6V Symbol tACC tCE tOE tDF tOH tRC tWC tCWC tAS tAH tDS tDH tVCS tCS tCH tOES tOEH DESCRIPTION Address to output delay OE=VIL Chip enable to output delay Output enable to output delay OE High to output float(Note1) Output hold time of from the rising edge of Address, CE, or OE, whichever happens first Read cycle time (Note 1) Write cycle time (Note 1) Command write cycle time(Note 1) Address setup time Address hold time Data setup time Data hold time Vcc setup time(Note 1) Chip enable setup time Chip enable hold time Output enable setup time (Note 1) Output enable hold time (Note 1) Read Toggle & Data Polling tWES tWEH tCEP tCEPH tWP tWPH tOLZ tWHGL Note: WE setup time WE hold time CE pulse width CE pulse width high WE pulse width WE pulse width high Output enable to output low Z WE high to OE going low MIN MIN MIN MIN MIN MIN MAX MIN 0 0 45 30 35 30 30 30 0 0 50 30 50 30 40 30 ns ns ns ns ns ns ns ns MIN MIN MIN MIN MIN MIN MIN MIN MIN MIN MIN MIN MIN 90 90 90 0 45 45 0 50 0 0 0 0 10 120 120 120 0 50 50 0 50 0 0 0 0 10 ns ns ns ns ns ns ns us ns ns ns ns ns OE=VIL MAX MAX MAX MIN 90 34 25 0 120 44 35 0 ns ns ns ns CONDITION CE=VIL MAX 90 90 120 120 Unit ns 1.Not 100% Tested 2.tr = tf = 5ns P/N:PM0827 REV. 0.4, JAN. 31, 2002 17 MX26L1620 Fig 1. COMMAND WRITE OPERATION VCC 5V Addresses VIH ADD Valid VIL tAS tAH WE VIH VIL tOES tWPH tCWC tWP CE VIH VIL tCS tCH OE VIH VIL VIH tDS tDH Data VIL DIN READ/RESET OPERATION Fig 2. READ TIMING WAVEFORMS tRC VIH Addresses VIL ADD Valid tCE CE VIH VIL WE VIH VIL tOEH tOLZ VIH tOE tDF OE VIL tACC tOH Outputs VOH VOL HIGH Z DATA Valid HIGH Z P/N:PM0827 REV. 0.4, JAN. 31, 2002 18 MX26L1620 AC CHARACTERISTICS Parameter tREADY tRP1 tRP2 tRH Description RESET PIN Low (NOT During Automatic Algorithms) to Read or Write (See Note) RESET Pulse Width (During Automatic Algorithms) RESET Pulse Width (NOT During Automatic Algorithms) RESET High Time Before Read(See Note) MIN MIN MIN 10 500 50 us ns ns Test Setup All Speed Options Unit MAX 500 ns Note:Not 100% tested Fig 3. RESET TIMING WAVFORM CE, OE tRH RESET tRP2 tReady Reset Timing NOT during Automatic Algorithms RESET tRP1 Reset Timing during Automatic Algorithms P/N:PM0827 REV. 0.4, JAN. 31, 2002 19 MX26L1620 ERASE/PROGRAM OPERATION Fig 4. AUTOMATIC CHIP ERASE TIMING WAVEFORM Erase Command Sequence(last two cycle) tWC tAS Read Status Data Address 2AAh 555h tAH VA VA CE tCH tGHWL OE tWHGL tWP tWHWH2 WE tCS tDS tDH tWPH 55h Data tVCS 10h In Progress Complete VCC P/N:PM0827 REV. 0.4, JAN. 31, 2002 20 MX26L1620 Fig 5. AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART START Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 80H Address 555H Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data 10H Address 555H Data Poll from system YES No DATA = FFh ? YES Auto Erase Completed P/N:PM0827 REV. 0.4, JAN. 31, 2002 21 MX26L1620 Fig 6. AUTOMATIC PROGRAM TIMING WAVEFORMS Program Command Sequence(last two cycle) tWC tAS Read Status Data (last two cycle) Address 555h PA tAH PA PA CE tCH tGHWL OE tWHGL tWP tWHWH1 WE tCS tDS tDH tWPH A0h Data tVCS PD Status DOUT VCC NOTES: 1.PA=Program Address, PD=Program Data, DOUT is the true data the program address Fig 7. Accelerated Program Timing Diagram (8.5V ~ 9.5V) VHH ACC VIL or VIH VIL or VIH tVHH tVHH P/N:PM0827 REV. 0.4, JAN. 31, 2002 22 MX26L1620 Fig 8. CE CONTROLLED PROGRAM TIMING WAVEFORM 555 for program 2AA for erase PA for program 555 for chip erase Data Polling Address tWC tWH tAS tAH PA WE tGHEL tWHGL OE tCP tWHWH1 or 2 CE tWS tDS tDH tCPH tBUSY Q7 DOUT Data tRH A0 for program 55 for erase PD for program 10 for chip erase RESET NOTES: 1.PA=Program Address, PD=Program Data, DOUT=Data Out, Q7=complement of data written to device. 2.Figure indicates the last two bus cycles of the command sequence. P/N:PM0827 REV. 0.4, JAN. 31, 2002 23 MX26L1620 Fig 9. AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART START Write Data AAH Address 555H Write Data 55H Address 2AAH Write Data A0H Address 555H Write Program Data/Address Increment Address Data Polling from system No Verify Word Ok ? YES No Last Address ? YES Auto Program Completed P/N:PM0827 REV. 0.4, JAN. 31, 2002 24 MX26L1620 Fig 10. SECURED SILICON SECTOR PROTECTED ALOGORITHMS FLOWCHART START Enter Secured Silicon Sector Wait 1us Frist Wait Cycle Data=60h Second Wait Cycle Data=60h A6=0, A1=1, A0=0 Wait 300us NO Data=01h? YES Device Failed Write Reset Command Secured Sector Protect Complete P/N:PM0827 REV. 0.4, JAN. 31, 2002 25 MX26L1620 Fig 11. SILICON ID READ TIMING WAVEFORM VCC 3V VID VIH VIL VIH VIL tACC tACC ADD A9 ADD A0 A1 VIH VIL VIH ADD VIL CE VIH VIL WE VIH VIL tCE OE VIH VIL tOE tDF tOH tOH VIH DATA Q0-Q15 DATA OUT VIL DATA OUT 22FE 00C2H P/N:PM0827 REV. 0.4, JAN. 31, 2002 26 MX26L1620 WRITE OPERATION STATUS Fig 12. DATA POLLING TIMING WAVEFORMS (DURING AUTOMATIC ALGORITHMS) tRC Address VA tACC tCE VA VA CE tCH tOE OE tOEH tDF WE tOH DQ7 Q0-Q6 Complement Complement True Valid Data High Z Status Data Status Data True Valid Data High Z NOTES: VA=Valid address. Figure shows are first status cycle after command sequence, last status read cycle, and array data read cycle. P/N:PM0827 REV. 0.4, JAN. 31, 2002 27 MX26L1620 Fig 13. Data Polling Algorithm START Read Q7~Q0 Add. = VA (1) Q7 = Data ? Yes No No Q5 = 1 ? Yes Read Q7~Q0 Add. = VA Yes Q7 = Data ? (2) No FAIL PASS Notes: 1.VA=valid address for programming. 2.Q7 should be rechecked even Q5="1"because Q7 may change simultaneously with Q5. P/N:PM0827 REV. 0.4, JAN. 31, 2002 28 MX26L1620 Fig 14. TOGGLE BIT TIMING WAVEFORMS (DURING AUTOMATIC ALOGRITHMS) tRC Address VA tACC tCE VA VA VA CE tCH tOE OE tOEH tDF WE tOH Q6/Q2 High Z Valid Status (first raed) Valid Status (second read) Valid Data (stops toggling) Valid Data NOTES: VA=Valid address; not required for Q6. Figure shows first two status cycle after command sequence, last status read cycle, and array data read cycle. P/N:PM0827 REV. 0.4, JAN. 31, 2002 29 MX26L1620 Fig 15. Toggle Bit Algorithm START Read Q7~Q0 Read Q7~Q0 (Note 1) Toggle Bit Q6 =Toggle? YES NO NO Q5=1? YES Read Q7~Q0 Twice (Note 1,2) Toggle Bit Q6= Toggle? YES Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Note: 1.Read toggle bit twice to determine whether or not it is toggling. 2.Recheck toggle bit because it may stop toggling as Q5 changes to "1". P/N:PM0827 REV. 0.4, JAN. 31, 2002 30 MX26L1620 ERASE AND PROGRAMMING PERFORMANCE(1) LIMITS PARAMETER Chip Erase Time Word Programming Time Chip Programming Time Accelerated Word Program Time Erase/Program Cycles Note: 100 MIN. TYP.(2) 45 30 35 7 MAX. 450 350 75 210 UNITS sec us sec us Cycles 1.Not 100% Tested, Excludes external system level over head. 2.Typical values measured at 25 C,3.3V. Additionally programming typicals assume checkerboard pattern. LATCHUP CHARACTERISTICS MIN. Input Voltage with respect to GND on all pins except I/O pins Input Voltage with respect to GND on all I/O pins Current Includes all pins except Vcc. Test conditions: Vcc = 5.0V, one pin at a time. -1.0V -1.0V -100mA MAX. 13.5V Vcc + 1.0V +100mA CAPACITANCE TA=0C to 70C, VCC=2.7V~3.6V Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Set VIN=0 VOUT=0 VIN=0 TYP 6 8.5 7.5 MAX 7.5 12 9 UNIT pF pF pF Notes: 1. Sampled, not 100% tested. 2. Test conditions TA=25 f=1.0MHz C, DATA RETENTION Parameter Minimum Pattern Data Retention Time Test Conditions 150 125 Min 10 20 Unit Years Years P/N:PM0827 REV. 0.4, JAN. 31, 2002 31 MX26L1620 ORDERING INFORMATION PLASTIC PACKAGE ACCESS TIME (ns) MX26L1620MC-90 90 MX26L1620MC-12 120 MX26L1620TC-90 90 MX26L1620TC-12 MX26L1620XAC-90 MX26L1620XAC-12 MX26L1620XBC-90 MX26L1620XBC-12 MX26L1620MI-90 MX26L1620MI-12 MX26L1620TI-90 MX26L1620TI-12 MX26L1620XAI-90 MX26L1620XAI-12 MX26L1620XBI-90 MX26L1620XBI-12 120 90 120 90 120 90 120 90 120 90 120 90 120 PART NO. Temperature Range Commerical Commerical Commerical Commerical Commerical Commerical Commerical Commerical Industrial Industrial Industrial Industrial Industrial Industrial Industrial Industrial Package type 44 pin SOP 44 pin SOP 48 pin TSOP (Normal Type) 48 pin TSOP (Normal Type) 48 ball CSP 48 ball CSP 48 ball CSP 48 ball CSP 44 pin SOP 44 pin SOP 48 pin TSOP (Normal Type) 48 pin TSOP (Normal Type) 48 ball CSP 48 ball CSP 48 ball CSP 48 ball CSP Ball Pitch 0.75 mm 0.75 mm 0.8 mm 0.8 mm 0.75 mm 0.75 mm 0.8 mm 0.8 mm P/N:PM0827 REV. 0.4, JAN. 31, 2002 32 MX26L1620 PACKAGE INFORMATION 48-PIN PLASTIC TSOP P/N:PM0827 REV. 0.4, JAN. 31, 2002 33 MX26L1620 44-Pin SOP P/N:PM0827 REV. 0.4, JAN. 31, 2002 34 MX26L1620 REVISION HISTORY Revision No. Description 0.1 1.To added the VI/O voltage range and performance 2.To modify Autoselect code table 3.To added Deep power-down mode 4.To added chip erase algorithm flowchart 5.To added secured silicon sector protect Algorithm flowchart 6.To modify the 14-pin of 48 TSOP package from NC to VCC 0.2 1.To added 44 SOP package 2.To modify the VI/O range from 1.8V~5V to 1.8V~3.6V 3.Cancel th regulated voltage range 4.Modify DC Characteristics table for VIL/VIH voltage when VI/O range is 1.8V~2.6V 0.3 1.To modify VI/O voltage range from 1.8V to 1.65V 2.To modify ICC4/tCS/tCH/tOLZ/tWHGL spec 3.To modify VCC standby current from 50uA to 30uA 4.Cancel the deep power down mode 5.To modify programming time 0.4 1.To modify the content error 2.To modify Fast erase time:23s/chip (typ.)-->45s/chip(typ.) Page P1,7 P5 P9,10 P23 P24 P2 P1,2,34 P1 14 P15 P1,8,15 P14,17 P1,15 P11,15 P31 P1,7,11 P1,5,31 Date JUL/23/2001 JUL/31/2001 SEP/26/2001 JAN/31/2002 P/N:PM0827 REV. 0.4, JAN. 31, 2002 35 MX26L1620 MACRONIX INTERNATIONAL CO., LTD. HEADQUARTERS: TEL:+886-3-578-6688 FAX:+886-3-563-2888 EUROPE OFFICE: TEL:+32-2-456-8020 FAX:+32-2-456-8021 JAPAN OFFICE: TEL:+81-44-246-9100 FAX:+81-44-246-9105 SINGAPORE OFFICE: TEL:+65-348-8385 FAX:+65-348-8096 TAIPEI OFFICE: TEL:+886-2-2509-3300 FAX:+886-2-2509-2200 MACRONIX AMERICA, INC. TEL:+1-408-453-8088 FAX:+1-408-453-8488 CHICAGO OFFICE: TEL:+1-847-963-1900 FAX:+1-847-963-1909 http : //www.macronix.com MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. |
Price & Availability of MX26L1620XBI-90
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |